KZ750 Twin | Rear Hoop Tail Light Pocket

Ok, let’s put a rear hoop on this KZ 750 twin. Charles came to me needing a little work. He wanted a rear hoop and tail light installed on his bike. So I said, no problem! Charles was also wanting the tail light to be set into the frame.

I first started out concentrating on the rear hoop. Measuring the distance between the frame rails I knew it was going to be wider than my dies diameter. I have run into this in the past and found that making smaller bends and bringing them together to make the right size hoop is the answer. The side effect is more of a pitched shape to the hoop rather than the conventional U shape, which I dig. I attached the hoop with solid slugs that are plug welded as well as welded at the seam.

Now on to the tail light “pocket”. This is all sheet metal work and I’m using 20ga steel. I made what I call the “backing plate” first. I trace an elongated oval and cut it out. Then I radius my piece to the same curve of the new hoop. For the “pocket” I bend 20ga around a piece of .5” OD round stock, making sure it’s a 180 degree bend. Then using the “backing plate” I trace out the excess material to be removed. After it’s removed the backing plate will take its place. At this point the tail light pocket is made and needs a place to go. I cut out a section of the new hoop to make room for the pocket.

Once I weld the pocket in it’s just a matter of cutting the protruding material to leave a clean profile in all directions. The light will be contoured to the hoop and set in the pocket. Now, Charles has a sweet custom hoop and more over his tail light is set in the frame!! I dig it and so did Charles!!

KZ440 |”Black Beauty”

before-after-kz440

 

Well, I finished Aaron’s Kawasaki 440 twin. I can say that I am stoked on the end result and Aaron was smiling when he rode off, so I think he liked it too. I thought the stock look was good, it just needed a little cleaning up. So in no particular order I shortened the subframe and hooped it in. I also made a new seat pan to match the new subframe, getting rid of the bulky stock seat. I shortened up the original fenders, cleaned and painted everything. Aaron designed the seat stitch pattern and polished the center of the gas tank. This was a fun bike to transform and a definite head turner!!

 

For Sale | Custom Kz750

 

THE STATS:

DONER BIKE: I started out with a stock 1980 Kawasaki Kz750 LTD.

DRIVE TRIAN: The 750cc motor has been completely torn down cleaned and all tolerances check against factory specifications. New piston rings were installed. I lapped and  re-shimmed the valves, and installed new valve seals. All gaskets and seals have been replaced. The carburetors received a rebuild kit and new jetting. The exhaust is a four into one header, with a baffle and packing in place for noise reduction and back pressure.

ELECTRICAL: A new wiring harness, new blade style fuse block, and a Shorai lithium battery (saves space and worry) were installed. A new regulator/rectifier from Ricks Motorsport was also put in place. I installed a Dyna ignition, coils, and plug wires. The turn signals and taillight are LED. New 2.5″ LED backlit tack and speedometer were installed. Handlebar controls include, turn signals, HI/LO beam, horn, and flash to pass switch.

BRAKES/SUSPENSION: The forks, wheels, brakes, and swing-arm are from a stock ’78 kz650. I did this swap because I didn’t like the height of the Kz750’s front-end and the original swing-arm bushings were bad. I had the Kz650’s running gear from another build so I put it to use. In doing this the Kz750’s ride height really leveled out, and bushing problem was fixed. The forks have been rebuild and resealed. The brakes received new seals and new EBC pads. It has a new radial master cylinder in front and rebuilt master in the rear, and new braided steel brake lines all around. The rear swing-arm has been modified and reinforced to a mono-shock set up, using a CBR929 shock.

FRAME/BODY: The frame has been modified to accept the mono-shock conversion. The subframe is totally new and designed to suit the new suspension. In the subframe under tray (under the seat) is where you will find all the electronics including the battery. All Balls tapered steering bearings were used to update the neck bearings. The gas tank has been scalloped which is not only aesthetically pleasing but holds your knees quite well. The headlight bracket doubles as a gauge mount, and has turn signals built in. I made the seat pan to fit, and sent it over to Gotcha Covered Upholstery where they always do an amazing job!! In painting the Kz750 I went with a tri-tone of ivory white, Kawasaki green, and jet black. I use a base coat clear coat system.

The Kz750 is a absolute joy to ride, and gets more than its fair share of looks going down the road.

$7,500

80′ kz750 | update

I’ve been busy trying to get this thing going. I’m almost there!!!! I’m just waiting on some brake seals, then a little test riding!!!